pci 0000:00:08.0: [10de:075a] type 1 class 0x000604 pci 0000:00:09.0: [10de:0ad0] type 0 class 0x000101 pci 0000:00:09.0: reg 10: [io 0xd480-0xd487] pci 0000:00:09.0: reg 14: [io 0xd400-0xd403] pci 0000:00:09.0: reg 18: [io 0xd080-0xd087] pci 0000:00:09.0: reg 1c: [io 0xd000-0xd003] pci 0000:00:09.0: reg 20: [io 0xcc00-0xcc0f] pci 0000:00:09.0: reg 24: [mem 0xfce76000-0xfce77fff] pci 0000:00:0a.0: [10de:0760] type 0 class 0x000200 pci 0000:00:0a.0: reg 10: [mem 0xfce7c000-0xfce7cfff] pci 0000:00:0a.0: reg 14: [io 0xc880-0xc887] pci 0000:00:0a.0: reg 18: [mem 0xfce7f400-0xfce7f4ff] pci 0000:00:0a.0: reg 1c: [mem 0xfce7f000-0xfce7f00f] pci 0000:00:0a.0: supports D1 D2 pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:0a.0: PME# disabled pci 0000:00:10.0: [10de:0778] type 1 class 0x000604 pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:10.0: PME# disabled pci 0000:00:12.0: [10de:075b] type 1 class 0x000604 pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:12.0: PME# disabled pci 0000:00:18.0: [1022:1100] type 0 class 0x000600 pci 0000:00:18.1: [1022:1101] type 0 class 0x000600 pci 0000:00:18.2: [1022:1102] type 0 class 0x000600 pci 0000:00:18.3: [1022:1103] type 0 class 0x000600 pci 0000:01:07.0: [1131:7146] type 0 class 0x000480 pci 0000:01:07.0: reg 10: [mem 0xfcfffc00-0xfcfffdff] pci 0000:00:08.0: PCI bridge to [bus 01-01] (subtractive decode) pci 0000:00:08.0: bridge window [io 0xf000-0x0000] (disabled) pci 0000:00:08.0: bridge window [mem 0xfcf00000-0xfcffffff] pci 0000:00:08.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) pci 0000:00:08.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) pci 0000:00:08.0: bridge window [io 0x0d00-0xffff] (subtractive decode) pci 0000:00:08.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) pci 0000:00:08.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode) pci 0000:00:08.0: bridge window [mem 0x80000000-0xdfffffff] (subtractive decode) pci 0000:00:08.0: bridge window [mem 0xf0000000-0xfebfffff] (subtractive decode) pci 0000:02:00.0: [10de:104a] type 0 class 0x000300 pci 0000:02:00.0: reg 10: [mem 0xfd000000-0xfdffffff] pci 0000:02:00.0: reg 14: [mem 0xf0000000-0xf7ffffff 64bit pref] pci 0000:02:00.0: reg 1c: [mem 0xfa000000-0xfbffffff 64bit pref] pci 0000:02:00.0: reg 24: [io 0xec00-0xec7f] pci 0000:02:00.0: reg 30: [mem 0xfe900000-0xfe97ffff pref] pci 0000:02:00.1: [10de:0e08] type 0 class 0x000403 pci 0000:02:00.1: reg 10: [mem 0xfe9fc000-0xfe9fffff] pci 0000:00:10.0: PCI bridge to [bus 02-02] pci 0000:00:10.0: bridge window [io 0xe000-0xefff] pci 0000:00:10.0: bridge window [mem 0xfd000000-0xfe9fffff] pci 0000:00:10.0: bridge window [mem 0xf0000000-0xfbffffff 64bit pref] pci 0000:03:00.0: [18c3:0720] type 0 class 0x000400 pci 0000:03:00.0: reg 10: [mem 0xfeaf0000-0xfeafffff] pci 0000:03:00.0: reg 14: [mem 0xfeae0000-0xfeaeffff 64bit] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' pci 0000:00:12.0: PCI bridge to [bus 03-03] pci 0000:00:12.0: bridge window [io 0xf000-0x0000] (disabled) pci 0000:00:12.0: bridge window [mem 0xfea00000-0xfeafffff] pci 0000:00:12.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) pci_bus 0000:00: on NUMA node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.MXR0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT] pci0000:00: Requesting ACPI _OSC control (0x1d) pci0000:00: ACPI _OSC request failed (AE_SUPPORT), returned control mask: 0x0c ACPI _OSC control for PCIe not granted, disabling ASPM ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *10 ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN0A] (IRQs 16 17 18 19) *10 ACPI: PCI Interrupt Link [LN0B] (IRQs 16 17 18 19) *11 ACPI: PCI Interrupt Link [LN0C] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN0D] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN1A] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN1B] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN1C] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN1D] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN2A] (IRQs 16 17 18 19) *11 ACPI: PCI Interrupt Link [LN2B] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN2C] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN2D] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN3A] (IRQs 16 17 18 19) *15 ACPI: PCI Interrupt Link [LN3B] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN3C] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN3D] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN4A] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN4B] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN4C] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN4D] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN5A] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN5B] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN5C] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN5D] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN6A] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN6B] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN6C] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN6D] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN7A] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN7B] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN7C] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LN7D] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *10 ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *15 ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *10 ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *15 ACPI: PCI Interrupt Link [SGRU] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11 ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *10 ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *5 ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *11 ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *10 vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none vgaarb: loaded vgaarb: bridge control possible 0000:02:00.0 SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Advanced Linux Sound Architecture Driver Version 1.0.24. PCI: Using ACPI for IRQ routing PCI: pci_cache_line_size set to 64 bytes reserve RAM buffer: 000000000009ec00 - 000000000009ffff reserve RAM buffer: 000000007ff90000 - 000000007fffffff HPET: 3 timers in total, 0 timers will be used for per-cpu timer Switching to clocksource hpet pnp: PnP ACPI init ACPI: bus type pnp registered pnp 00:00: [bus 00-ff] pnp 00:00: [io 0x0cf8-0x0cff] pnp 00:00: [io 0x0000-0x0cf7 window] pnp 00:00: [io 0x0d00-0xffff window] pnp 00:00: [mem 0x000a0000-0x000bffff window] pnp 00:00: [mem 0x000d0000-0x000dffff window] pnp 00:00: [mem 0x80000000-0xdfffffff window] pnp 00:00: [mem 0xf0000000-0xfebfffff window] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) pnp 00:01: [dma 4] pnp 00:01: [io 0x0000-0x000f] pnp 00:01: [io 0x0081-0x0083] pnp 00:01: [io 0x0087] pnp 00:01: [io 0x0089-0x008b] pnp 00:01: [io 0x008f] pnp 00:01: [io 0x00c0-0x00df] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) pnp 00:02: [io 0x0061] pnp 00:02: Plug and Play ACPI device, IDs PNP0800 (active) pnp 00:03: [io 0x00f0-0x00ff] pnp 00:03: [irq 13] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) pnp 00:04: [io 0x0378-0x037f] pnp 00:04: [irq 7] pnp 00:04: [dma 0 disabled] pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active) pnp 00:05: [mem 0x000d0000-0x000d3fff window] pnp 00:05: [mem 0x000d4000-0x000d7fff window] pnp 00:05: [mem 0x000de000-0x000dffff window] pnp 00:05: [io 0x0010-0x001f] pnp 00:05: [io 0x0022-0x003f] pnp 00:05: [io 0x0044-0x004d] pnp 00:05: [io 0x0050-0x005f] pnp 00:05: [io 0x0062-0x0063] pnp 00:05: [io 0x0065-0x006f] pnp 00:05: [io 0x0072-0x007f] pnp 00:05: [io 0x0080] pnp 00:05: [io 0x0084-0x0086] pnp 00:05: [io 0x0088] pnp 00:05: [io 0x008c-0x008e] pnp 00:05: [io 0x0090-0x009f] pnp 00:05: [io 0x00a2-0x00bf] pnp 00:05: [io 0x00e0-0x00ef] pnp 00:05: [io 0x04d0-0x04d1] pnp 00:05: [io 0x0800-0x080f] pnp 00:05: [io 0x0500-0x057f] pnp 00:05: [io 0x0580-0x05ff] pnp 00:05: [io 0x0800-0x087f] pnp 00:05: [io 0x0880-0x08ff] pnp 00:05: [io 0x0d00-0x0d7f] pnp 00:05: [io 0x0d80-0x0dff] pnp 00:05: [io 0x0900-0x097f] pnp 00:05: [io 0x0980-0x09ff] pnp 00:05: [mem 0x00000000-0xffffffff disabled] pnp 00:05: [mem 0x00000000-0xffffffff disabled] pnp 00:05: [mem 0xfed04000-0xfed04fff] pnp 00:05: [mem 0xfee01000-0xfeefffff] pnp 00:05: disabling [io 0x0900-0x097f] because it overlaps 0000:00:01.0 BAR 0 [io 0x0900-0x09ff] pnp 00:05: disabling [io 0x0980-0x09ff] because it overlaps 0000:00:01.0 BAR 0 [io 0x0900-0x09ff] system 00:05: [io 0x04d0-0x04d1] has been reserved system 00:05: [io 0x0800-0x080f] has been reserved system 00:05: [io 0x0500-0x057f] has been reserved system 00:05: [io 0x0580-0x05ff] has been reserved system 00:05: [io 0x0800-0x087f] could not be reserved system 00:05: [io 0x0880-0x08ff] has been reserved system 00:05: [io 0x0d00-0x0d7f] has been reserved system 00:05: [io 0x0d80-0x0dff] has been reserved system 00:05: [mem 0x000d0000-0x000d3fff window] has been reserved system 00:05: [mem 0x000d4000-0x000d7fff window] has been reserved system 00:05: [mem 0x000de000-0x000dffff window] has been reserved system 00:05: [mem 0xfed04000-0xfed04fff] has been reserved system 00:05: [mem 0xfee01000-0xfeefffff] has been reserved system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) pnp 00:06: [mem 0xfed00000-0xfed00fff] pnp 00:06: [irq 2 disabled] pnp 00:06: [irq 8] pnp 00:06: Plug and Play ACPI device, IDs PNP0103 (active) pnp 00:07: [io 0x0070-0x0071] pnp 00:07: Plug and Play ACPI device, IDs PNP0b00 (active) pnp 00:08: [io 0x0060] pnp 00:08: [io 0x0064] pnp 00:08: [mem 0xfec00000-0xfec00fff] pnp 00:08: [mem 0xfee00000-0xfee00fff] system 00:08: [mem 0xfec00000-0xfec00fff] could not be reserved system 00:08: [mem 0xfee00000-0xfee00fff] has been reserved system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active) pnp 00:09: [io 0x0000-0xffffffff disabled] pnp 00:09: [io 0x0230-0x023f] pnp 00:09: [io 0x0290-0x029f] pnp 00:09: [io 0x0a00-0x0a0f] pnp 00:09: [io 0x0a10-0x0a1f] system 00:09: [io 0x0230-0x023f] has been reserved system 00:09: [io 0x0290-0x029f] has been reserved system 00:09: [io 0x0a00-0x0a0f] has been reserved system 00:09: [io 0x0a10-0x0a1f] has been reserved system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active) pnp 00:0a: [io 0x03f8-0x03ff] pnp 00:0a: [irq 4] pnp 00:0a: [dma 0 disabled] pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active) pnp 00:0b: [mem 0xe0000000-0xefffffff] system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active) pnp 00:0c: [mem 0x00000000-0x0009ffff] pnp 00:0c: [mem 0x000c0000-0x000cffff] pnp 00:0c: [mem 0x000e0000-0x000fffff] pnp 00:0c: [mem 0x00100000-0x7fffffff] pnp 00:0c: [mem 0xfec00000-0xffffffff] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved system 00:0c: [mem 0x000c0000-0x000cffff] could not be reserved system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved system 00:0c: [mem 0x00100000-0x7fffffff] could not be reserved system 00:0c: [mem 0xfec00000-0xffffffff] could not be reserved system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active) pnp: PnP ACPI: found 13 devices ACPI: ACPI bus type pnp unregistered PCI: max bus depth: 1 pci_try_num: 2 pci 0000:00:08.0: PCI bridge to [bus 01-01] pci 0000:00:08.0: bridge window [io disabled] pci 0000:00:08.0: bridge window [mem 0xfcf00000-0xfcffffff] pci 0000:00:08.0: bridge window [mem pref disabled] pci 0000:00:10.0: PCI bridge to [bus 02-02] pci 0000:00:10.0: bridge window [io 0xe000-0xefff] pci 0000:00:10.0: bridge window [mem 0xfd000000-0xfe9fffff] pci 0000:00:10.0: bridge window [mem 0xf0000000-0xfbffffff 64bit pref] pci 0000:00:12.0: PCI bridge to [bus 03-03] pci 0000:00:12.0: bridge window [io disabled] pci 0000:00:12.0: bridge window [mem 0xfea00000-0xfeafffff] pci 0000:00:12.0: bridge window [mem pref disabled] pci 0000:00:08.0: setting latency timer to 64 ACPI: PCI Interrupt Link [LN0A] enabled at IRQ 19 pci 0000:00:10.0: PCI INT A -> Link[LN0A] -> GSI 19 (level, low) -> IRQ 19 pci 0000:00:10.0: setting latency timer to 64 ACPI: PCI Interrupt Link [LN2A] enabled at IRQ 18 pci 0000:00:12.0: PCI INT A -> Link[LN2A] -> GSI 18 (level, low) -> IRQ 18 pci 0000:00:12.0: setting latency timer to 64 pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff] pci_bus 0000:00: resource 8 [mem 0x80000000-0xdfffffff] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xfebfffff] pci_bus 0000:01: resource 1 [mem 0xfcf00000-0xfcffffff] pci_bus 0000:01: resource 4 [io 0x0000-0x0cf7] pci_bus 0000:01: resource 5 [io 0x0d00-0xffff] pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff] pci_bus 0000:01: resource 7 [mem 0x000d0000-0x000dffff] pci_bus 0000:01: resource 8 [mem 0x80000000-0xdfffffff] pci_bus 0000:01: resource 9 [mem 0xf0000000-0xfebfffff] pci_bus 0000:02: resource 0 [io 0xe000-0xefff] pci_bus 0000:02: resource 1 [mem 0xfd000000-0xfe9fffff] pci_bus 0000:02: resource 2 [mem 0xf0000000-0xfbffffff 64bit pref] pci_bus 0000:03: resource 1 [mem 0xfea00000-0xfeafffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. pci 0000:00:07.0: Enabling HT MSI Mapping pci 0000:00:08.0: Enabling HT MSI Mapping pci 0000:00:09.0: Enabling HT MSI Mapping pci 0000:00:0a.0: Enabling HT MSI Mapping pci 0000:02:00.0: Boot video device PCI: CLS 64 bytes, default 64 Trying to unpack rootfs image as initramfs... Freeing initrd memory: 444k freed audit: initializing netlink socket (disabled) type=2000 audit(1373262918.428:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.30 [Flags: R/W]. JFS: nTxBlock = 8192, nTxLock = 65536 SGI XFS with security attributes, large block/inode numbers, no debug enabled Btrfs loaded msgmni has been set to 1726 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A lp: driver loaded but no devices found Non-volatile memory driver v1.3 Linux agpgart interface v0.103 uvesafb: NVIDIA Corporation, GF119 Board - 13100004, Chip Rev , OEM: NVIDIA, VBE v3.0 uvesafb: protected mode interface info at c000:c580 uvesafb: pmi: set display start = c00cc5e3, set palette = c00cc63e uvesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da uvesafb: VBIOS/hardware doesn't support DDC transfers uvesafb: no monitor limits have been set, default refresh rate will be used uvesafb: scrolling: ywrap using protected mode interface, yres_virtual=9175 Console: switching to colour frame buffer device 100x37 uvesafb: framebuffer at 0xfb000000, mapped to 0xf8500000, using 14336k, total 14336k fb0: VESA VGA frame buffer device input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 ACPI: Power Button [PWRB] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 ACPI: Power Button [PWRF] ACPI: acpi_idle registered with cpuidle isapnp: Scanning for PnP cards... fbcondecor: console 0 using theme 'g2v' fbcondecor: switched decor state to 'on' on console 0 isapnp: No Plug & Play device found parport_pc 00:04: reported by Plug and Play ACPI parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] lp0: using parport0 (interrupt-driven). brd: module loaded loop: module loaded rbd: loaded rbd (rados block device) 3ware Storage Controller device driver for Linux v1.26.02.003. 3ware 9000 Storage Controller device driver for Linux v2.26.02.014. LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000. ahci 0000:00:09.0: version 3.0 ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 ahci 0000:00:09.0: PCI INT A -> Link[LSA0] -> GSI 23 (level, low) -> IRQ 23 ahci 0000:00:09.0: irq 40 for MSI/MSI-X ahci 0000:00:09.0: controller can't do PMP, turning off CAP_PMP ahci 0000:00:09.0: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl IDE mode ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pio boh ahci 0000:00:09.0: setting latency timer to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 abar m8192@0xfce76000 port 0xfce76100 irq 40 ata2: SATA max UDMA/133 abar m8192@0xfce76000 port 0xfce76180 irq 40 ata3: SATA max UDMA/133 abar m8192@0xfce76000 port 0xfce76200 irq 40 ata4: SATA max UDMA/133 abar m8192@0xfce76000 port 0xfce76280 irq 40 ata5: SATA max UDMA/133 abar m8192@0xfce76000 port 0xfce76300 irq 40 ata6: SATA max UDMA/133 abar m8192@0xfce76000 port 0xfce76380 irq 40 pata_amd 0000:00:06.0: version 0.4.1 pata_amd 0000:00:06.0: setting latency timer to 64 scsi6 : pata_amd scsi7 : pata_amd ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 usbmon: debugfs is not available ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22 ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUB2] -> GSI 22 (level, low) -> IRQ 22 ehci_hcd 0000:00:02.1: setting latency timer to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.1: debug port 1 ehci_hcd 0000:00:02.1: cache line size of 64 is not supported ehci_hcd 0000:00:02.1: irq 22, io mem 0xfce7fc00 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 3.0.6-gentoo ehci_hcd usb usb1: SerialNumber: 0000:00:02.1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ACPI: PCI Interrupt Link [UB12] enabled at IRQ 21 ehci_hcd 0000:00:04.1: PCI INT B -> Link[UB12] -> GSI 21 (level, low) -> IRQ 21 ehci_hcd 0000:00:04.1: setting latency timer to 64 ehci_hcd 0000:00:04.1: EHCI Host Controller ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:04.1: debug port 1 ehci_hcd 0000:00:04.1: cache line size of 64 is not supported ehci_hcd 0000:00:04.1: irq 21, io mem 0xfce7f800 ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: EHCI Host Controller usb usb2: Manufacturer: Linux 3.0.6-gentoo ehci_hcd usb usb2: SerialNumber: 0000:00:04.1 hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 20 ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 20 (level, low) -> IRQ 20 ohci_hcd 0000:00:02.0: setting latency timer to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:02.0: irq 20, io mem 0xfce7e000 usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: OHCI Host Controller usb usb3: Manufacturer: Linux 3.0.6-gentoo ohci_hcd usb usb3: SerialNumber: 0000:00:02.0 hub 3-0:1.0: USB hub found hub 3-0:1.0: 6 ports detected ACPI: PCI Interrupt Link [UB11] enabled at IRQ 23 ohci_hcd 0000:00:04.0: PCI INT A -> Link[UB11] -> GSI 23 (level, low) -> IRQ 23 ohci_hcd 0000:00:04.0: setting latency timer to 64 ohci_hcd 0000:00:04.0: OHCI Host Controller ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:04.0: irq 23, io mem 0xfce7d000 usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: OHCI Host Controller usb usb4: Manufacturer: Linux 3.0.6-gentoo ohci_hcd usb usb4: SerialNumber: 0000:00:04.0 hub 4-0:1.0: USB hub found hub 4-0:1.0: 6 ports detected uhci_hcd: USB Universal Host Controller Interface driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver yurex i8042: PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mousedev: PS/2 mouse device common for all mice rtc_cmos 00:07: RTC can wake from S4 rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs cpufreq-nforce2: No nForce2 chipset. cpuidle: using governor ladder usbcore: registered new interface driver usbhid usbhid: USB HID core driver input: Speakup as /devices/virtual/input/input2 initialized device: /dev/synth, node (MAJOR 10, MINOR 25) speakup 3.1.6: initialized synth name on entry is: (null) ALSA device list: No soundcards found. oprofile: using NMI interrupt. TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 Registering the dns_resolver key type libceph: loaded (mon/osd proto 15/24, osdmap 5/6 5/6) Using IPI No-Shortcut mode rtc_cmos 00:07: setting system clock to 2013-07-08 05:55:20 UTC (1373262920) powernow-k8: Found 1 AMD Athlon(tm) Dual Core Processor 4850e (2 cpu cores) (version 2.20.00) powernow-k8: fid 0x11 (2500 MHz), vid 0x10 powernow-k8: fid 0x10 (2400 MHz), vid 0x11 powernow-k8: fid 0xe (2200 MHz), vid 0x13 powernow-k8: fid 0xc (2000 MHz), vid 0x15 powernow-k8: fid 0xa (1800 MHz), vid 0x15 powernow-k8: fid 0x2 (1000 MHz), vid 0x16 ata6: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata5: SATA link down (SStatus 0 SControl 300) ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATAPI: TSSTcorpDVD-ROM SH-D163A, SB01, max UDMA/33 ata1.00: ATA-8: Hitachi HDS723020BLE640, MX4OAAB0, max UDMA/133 ata1.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/33 ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA Hitachi HDS72302 MX4O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA scsi 2:0:0:0: CD-ROM TSSTcorp DVD-ROM SH-D163A SB01 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 4x/48x cd/rw xa/form2 cdda tray cdrom: Uniform CD-ROM driver Revision: 3.20 sr 2:0:0:0: Attached scsi CD-ROM sr0 ata8: port disabled. ignoring. sda: sda1 sda2 sda3 sda4 < sda5 > sd 0:0:0:0: [sda] Attached SCSI disk EXT3-fs: barriers not enabled kjournald starting. Commit interval 5 seconds EXT3-fs (sda2): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) readonly on device 8:2. devtmpfs: mounted Freeing unused kernel memory: 400k freed usb 3-2: new low speed USB device number 2 using ohci_hcd usb 3-2: New USB device found, idVendor=1241, idProduct=1503 usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 3-2: Product: USB Keyboard usb 3-2: Manufacturer: input: USB Keyboard as /devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.0/input/input3 generic-usb 0003:1241:1503.0001: input,hidraw0: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:02.0-2/input0 input: USB Keyboard as /devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.1/input/input4 generic-usb 0003:1241:1503.0002: input,hidraw1: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:02.0-2/input1 usb 3-5: new low speed USB device number 3 using ohci_hcd usb 3-5: New USB device found, idVendor=15c2, idProduct=ffdc usb 3-5: New USB device strings: Mfr=0, Product=0, SerialNumber=0 udev[1728]: starting version 164 EXT3-fs (sda2): using internal journal HDA Intel 0000:00:07.0: power state changed by ACPI to D0 HDA Intel 0000:00:07.0: power state changed by ACPI to D0 ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22 HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 22 (level, low) -> IRQ 22 hda_intel: Disabling MSI HDA Intel 0000:00:07.0: setting latency timer to 64 hda-intel: Enable delay in RIRB handling SKU: Nid=0x1d sku_cfg=0x4015e601 SKU: port_connectivity=0x1 SKU: enable_pcbeep=0x1 SKU: check_sum=0x00000005 SKU: customization=0x000000e6 SKU: external_amp=0x0 SKU: platform_type=0x0 SKU: swap=0x0 SKU: override=0x1 ACPI: PCI Interrupt Link [LN0B] enabled at IRQ 17 HDA Intel 0000:02:00.1: PCI INT B -> Link[LN0B] -> GSI 17 (level, low) -> IRQ 17 hda_intel: Disabling MSI HDA Intel 0000:02:00.1: setting latency timer to 64 hda-intel: Enable delay in RIRB handling HDMI status: Pin=4 Presence_Detect=0 ELD_Valid=0 HDMI status: Pin=5 Presence_Detect=0 ELD_Valid=0 WARNING: You are using an experimental version of the media stack. As the driver is backported to an older kernel, it doesn't offer enough quality for its usage in production. Use it with care. Latest git patches (needed if you report a bug to linux-media@vger.kernel.org): ed72d37a33fdf43dc47787fe220532cdec9da528 [media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff) b9e2afff1e6b36d05a0e12b6114eb0aaf8949c09 [media] rtl28xxu: Add USB IDs for Compro VideoMate U620F 676fa7d4c9fd141a31cba2870e592a597c0bb07f [media] em28xx: add usb id for terratec h5 rev. 3 experimental: fd75740ebaa7cfc4cbff5ca2daaf637de9a34114 experimental: Remove saa716x patches which were applied upstream. ngene-octopus-test: 406ffecccbec6e22da954a07b7398292330bc767 ddbridge: Add ID of Digital Devices Octopus V3. v4l-dvb-saa716x: cfa4b4faab67367b8012bcd49156e977fe235edc saa716x: remove __devinit and friends input: iMON Panel, Knob and Mouse(15c2:ffdc) as /devices/pci0000:00/0000:00:02.0/usb3/3-5/3-5:1.0/input/input5 imon 3-5:1.0: 0xffdc iMON LCD, MCE IR (id 0x9f) imon 3-5:1.0: imon_set_display_type: overriding display type to 2 via modparam Registered IR keymap rc-imon-mce input: iMON Remote (15c2:ffdc) as /devices/pci0000:00/0000:00:02.0/usb3/3-5/3-5:1.0/rc/rc0/input6 rc0: iMON Remote (15c2:ffdc) as /devices/pci0000:00/0000:00:02.0/usb3/3-5/3-5:1.0/rc/rc0 imon 3-5:1.0: iMON device (15c2:ffdc, intf0) on usb<3:3> initialized usbcore: registered new interface driver imon forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64. ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 21 forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21 forcedeth 0000:00:0a.0: setting latency timer to 64 forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:24:8c:60:60:bf forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim msi desc-v3 WARNING: You are using an experimental version of the media stack. As the driver is backported to an older kernel, it doesn't offer enough quality for its usage in production. Use it with care. Latest git patches (needed if you report a bug to linux-media@vger.kernel.org): ed72d37a33fdf43dc47787fe220532cdec9da528 [media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff) b9e2afff1e6b36d05a0e12b6114eb0aaf8949c09 [media] rtl28xxu: Add USB IDs for Compro VideoMate U620F 676fa7d4c9fd141a31cba2870e592a597c0bb07f [media] em28xx: add usb id for terratec h5 rev. 3 experimental: fd75740ebaa7cfc4cbff5ca2daaf637de9a34114 experimental: Remove saa716x patches which were applied upstream. ngene-octopus-test: 406ffecccbec6e22da954a07b7398292330bc767 ddbridge: Add ID of Digital Devices Octopus V3. v4l-dvb-saa716x: cfa4b4faab67367b8012bcd49156e977fe235edc saa716x: remove __devinit and friends saa7146: register extension 'budget dvb' ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 16 budget dvb 0000:01:07.0: PCI INT A -> Link[LNKB] -> GSI 16 (level, low) -> IRQ 16 saa7146: found saa7146 @ mem f9666c00 (revision 1, irq 16) (0x13c2,0x101c) saa7146 (0): dma buffer size 192512 DVB: registering new adapter (TT-Budget S2-1600 PCI) adapter has MAC addr = 00:d0:5c:cc:af:2b stv6110x_attach: Attaching STV6110x budget dvb 0000:01:07.0: DVB: registering adapter 0 frontend 0 (STV090x Multistandard)... nGene PCIE bridge driver, Copyright (C) 2005-2007 Micronas ngene 0000:03:00.0: PCI INT A -> Link[LN2A] -> GSI 18 (level, low) -> IRQ 18 ngene: Found Linux4Media cineS2 DVB-S2 Twin Tuner ngene 0000:03:00.0: setting latency timer to 64 ngene: Device version 1 ngene: Loading firmware file ngene_18.fw. ngene 0000:03:00.0: irq 41 for MSI/MSI-X error in i2c_read_reg No CXD2099 detected at 40 LNBx2x attached on addr=b stv6110x_attach: Attaching STV6110x DVB: registering new adapter (nGene) ngene 0000:03:00.0: DVB: registering adapter 1 frontend 0 (STV090x Multistandard)... LNBx2x attached on addr=8 stv6110x_attach: Attaching STV6110x DVB: registering new adapter (nGene) ngene 0000:03:00.0: DVB: registering adapter 2 frontend 0 (STV090x Multistandard)... XFS (sda5): Mounting Filesystem XFS (sda5): Ending clean mount